Step Tutorial for Bathtub Installation
Step Tutorial for Bathtub Installation
Blog Article
We've uncovered the article pertaining to How to Install a Bathtub Yourself listed below on the internet and decided it made good sense to write about it with you on my blog.
Setting up a bath tub isn't exactly brain surgery, but it does require solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately difficult job. If the old bathtub is conveniently available, the job can relocate speedily; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit attempting it. Instead of working with a service provider to take over a halfway-completed job, it is better to take into consideration employing one prior to you begin. Opportunities are you might require a professional plumber to make tube links.
This post will assist you mount a new bathtub in your washroom if you have currently purchased a new bathtub and don't need to transform the setup of your previous supply of water pipes.
Your tools and material list ought to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the water system. After doing so, turn on the taps to drain any water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome as a result of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Protect the faucet in place with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of both wooden boards under its feet, position the tub in the called for placement. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub up until the spirit level checks out level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Switch on the supply of water and inspect all joints and also new pipework for leaks and tighten them if necessary. Fill up the tub as well as also check the overflow electrical outlet and also the typical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait until the bathtub has actually been made use of a minimum of once as this will settle it right into its final setting.
Getting ready for the Setup
First of all, the sustaining structure supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, causing the water to permeate the wall surface in between the bath and also the tiling, leading to problems with wetness as well as feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently offered on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very involved in How to Install a Bathtub Yourself and I hope you enjoyed reading my blog entry. Are you aware of anybody else who is fascinated by the subject? Feel free to share it. We love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Pipe issues? Connect. Report this page